GL Announces ExpertSAM to Quad Port Ethernet/IP Tester
GL Communications Inc., announced today its enhanced PacketExpert™, a Quad Port Ethernet/IP Tester. It is enhanced with ITU-T Y.1564 test methodology referred to as ExpertSAM.
- (1888PressRelease) October 22, 2014 - Gaithersburg, Maryland, USA - Speaking to reporters, Mr. Jagdish Vadalia, a Senior Manager for Product Development of the company said, "GL's PacketExpert™ is a portable (USB based) Quad Port Ethernet / VLAN / MPLS / IP / UDP Tester with 4 Electrical Ethernet ports. 2 of the 4 ports can be Electrical or Optical, enabling testing on optical fiber links. The electrical ports support 10/100/1000 Mbps. The optical ports support 1000 Mbps using SFP Transceiver. Each GigE port supports testing at wire speed for applications such as Wire-Speed BERT, RFC 2544 (Single and Dual Port) Testing, Smart Loopback, WAN IP link Emulation, Capture and Playback, and ExpertSAM."
He added, "ExpertSAM is a set of test procedures that test the ability of Ethernet-based services to carry a variety of traffic (voice, data, and video) at defined performance levels. In particular, it is aimed at addressing limitations of legacy RFC 2544 test procedures, especially for Service Level Agreements (SLA). It performs round-trip measurements in combination with a remote loopback. In the above test setup depicted pictorially, another PacketExpert™ is configured as a loopback device. In this case, the results reflect the average of both Tx and Rx test directions."
Mr. Vadalia further explained, "ExpertSAM is a single test conducted to validate SLA. The ITU-T Y.1564 is built around two key subtests: the Service Configuration Test (SCT) and the Service Performance Test (SPT).
SCT includes sequential testing of each service validating the SLA parameters. A ramp test for each service is performed to verify the Committed Information Rate (CIR), and Excess Information Rate (EIR). Each service is validated within the specified time duration in seconds, which is uniform across all the services.
In ITU-T Y.1564 ExpertSAM test methodology, Throughput, Frame Loss, Frame Delay and Frame Delay Variation (cumulatively known as Service Acceptance Criteria, or SAC Parameters) are measured and compared to the expected values for each service ensuring it is within its committed range or the threshold defined for guaranteed traffic such as CIR.
User has been provided with the option to configure SPT in steps namely CIR, EIR and Traffic Policing. CIR can be configured either as Simple CIR (single step) or Step Load CIR (multiple steps). Each CIR step can be configured in % of CIR rate. Duration of each step can be from 1 to 60 seconds.
Once the configuration of each service is validated, the SPT simultaneously validates the quality of all the services traversing the network under full load with the SLA parameters over time. The SPT may take few minutes, or can be transitioned to longer testing hours."
Important Features
•Complete validation of Ethernet SLA in a single test
•Compliance with ITU-T Y.1564 standard SCT and SPT
•Supports multiple services (up to 12 services) with varying performance requirements that meets full load conditions
•Simultaneous validation of all the services for quality over the time
•Capability to generate traffic at throughput of CIR (guaranteed traffic), EIR (best effort bandwidth) and Traffic Policing (dropped bandwidth) rates ensuring Key Performance Indicators (KPI) validation
•Acceptable SLA parameter configuration for Information Rate (IR) or Throughput, Frame Loss Ratio (FLR), Frame Transfer Delay (FTD) and Frame Delay Variation (FDV) or Jitter and Pass/Fail verdict declared
•Color Aware Mode supported - generates Green/Yellow color marked traffic at the configured rates, and provides Green and Yellow measurements separately. VLAN PCP, IP TOS and IP DSCP color marking supported
•Ethernet MIX (EMIX) frame sizes supported per service - up to 7 frame sizes can be defined per service
•Stacked VLAN supported - Customer Tag (C-Tag) and Service Tag (S-Tag) to simulate Carrier Ethernet traffic
•Command Line Interface for automated testing and remote accessibility
About GL Communications Inc.,
Founded in 1986, GL Communications Inc. is a leading supplier of test, monitoring, and analysis equipment for TDM, Wireless, IP, and VoIP networks. Unlike conventional test equipment, GL's test platforms provide visualization, capture, storage, and convenient features like portability, remote operation, and scripting.
Our test solutions cover wide array of networks - 4G (LTE), 3G, 2G, IP, Ethernet, T1, T3, E1, E3, OC-3/STM-1, OC-12/STM-4, and analog. GL's tools are widely used by the telecommunication industry for: conformance testing, automated stress/load testing, and performance assessment, and analysis. For more information about GL's complete line of products,
Contact:
Shelley Sharma
Phone: 301-670-4784
E-mail: info at gl.com
###
space
space
Satisfied Users & 
Approved Press Releases
Print
Email
Report Spam